Insights · Reference

Duct Elbow Machines: How Round Elbows Are Made, and the Gorelocker Specs (2026)

A round duct elbow is built from gore segments closed one joint at a time on a gorelocker. This reference explains the gored-elbow process and lists the Taokron machines that do it — the hydraulic Gorelocker SBEM-1250, the electric Gorelockers SBWT-1000 and SBWT-1500, and the Fitting Shaper SBJQJ-500 — with diameter range, material thickness, speed, power and weight taken verbatim from the Taokron Product Catalog 2026.

Also in: العربية · Español · Français · Bahasa Indonesia · Português · Русский · Türkçe

How a gored elbow goes together

Round duct changes direction with a gored elbow: the elbow is divided into ring segments — gores — each cut at an angle so that stacked together they sweep through the bend. The gores are cut from sheet or coil, rolled round, and then joined gore-to-gore with a circumferential lock seam. The machine that folds and closes that seam is the gorelocker (you will also see it written gore locker or called an elbow lock-seaming machine). A mechanical seam holds the angle without welding, keeps the galvanised coating intact, and is the standard construction for elbows in galvanised, stainless and aluminium duct. In common practice a 90° elbow uses three to five gores — more gores, smoother sweep, lower pressure loss. The gore blanks themselves come off the cutting bench; see the duct cutting machine comparison for that end of the workflow.

The machines that close the seam

Taokron builds gorelockers in two drive types, hydraulic and electric, plus the fitting shaper for the small-diameter end of the range. The table lists every machine with the figures from the catalog. Speeds are given in the catalog unit: line speed in m/min for the hydraulic SBEM-1250, roll speed in r/min for the electric SBWT, so the two figures are not directly comparable.

MachineModelDiameterMaterial thicknessMax forming speedPowerWeight
Gorelocker (Hydraulic)SBEM-1250Φ100–Φ1250 mmGalvanised / black / aluminium 0.4–1.5 mm
Stainless 0.4–1.0 mm
120 m/min4 kW + 120 W cooling fan750 kg
Gorelocker (Electric)SBWT-1000 (A / D)Φ120–Φ1000 mmGalvanised 0.4–1.2 mm
Stainless SS304 0.4–0.8 mm
75 r/min1.5 kW×2 + 2.2 kW (A)
1.5 kW×2 + 2.2 kW×2 (D)
600 kg
Gorelocker (Electric)SBWT-1500 (A / D)Φ120–Φ1500 mmGalvanised 0.4–1.5 mm
Stainless SS304 0.4–1.2 mm
75 r/min2.2 kW×2 + 2.2 kW (A)
2.2 kW×2 + 2.2 kW×2 (D)
660 kg
Fitting ShaperSBJQJ-500Φ90–Φ400 mmGalvanised / stainless / aluminium 0.4–1.0 mm—3.5 kW1500 kg

Source: Taokron Product Catalog 2026, manufacturer nameplate specifications. All machines run 380 V / 50 Hz / 3-phase (60 Hz on request). SBEM-1250: 70 L hydraulic oil, flange size 5 / 7.5 / 10 mm, 3000×820×1100 mm. SBWT-1000: 2080×700×895 mm. SBWT-1500: 2450×700×895 mm. Electric models are frequency-controlled.

Hydraulic vs electric — and the A/D variants

Hydraulic (SBEM-1250). One machine covers Φ100–Φ1250 mm and the heaviest mixed-material work: galvanised, black steel and aluminium to 1.5 mm, stainless to 1.0 mm, forming at up to 120 m/min. It also rolls a 5, 7.5 or 10 mm flange on the gore edge, which suits shops that finish elbow ends in the same pass.

Electric (SBWT-1000 / SBWT-1500). Frequency-controlled at up to 75 r/min, lighter (600–660 kg) and more compact. Each comes in two variants: the A model forms the male and female gore edges; the D model adds the seam-lock closing head (Male/Female/Seam Lock) with a second drive set. If you want one electric machine to take a gore joint from formed edges to a closed seam, specify the D.

Small fittings. Below roughly Φ400 mm the practical companion is the Fitting Shaper SBJQJ-500, which forms the ends of elbows, tees, reducers and branches from Φ90 mm in galvanised, stainless and aluminium.

The deciding numbers are your largest elbow diameter and heaviest gauge: Φ1000 mm tops the SBWT-1000, Φ1250 mm the SBEM-1250, Φ1500 mm the SBWT-1500. For stainless above 1.0 mm the SBWT-1500 (SS304 to 1.2 mm) is the only fit. Round elbows pair with straight spiral duct off a spiral tubeformer; for the full fittings workflow including tees and reducers see the fittings fabrication guide.

Get a gorelocker recommendation in 12 hours →

FAQ

What is a gorelocker?

The machine that closes the circumferential lock seam joining the gore segments of a round duct elbow. Gores are cut and rolled first; the gorelocker folds and closes the seam between each pair so the elbow holds its angle without welding. Taokron builds hydraulic (SBEM-1250) and electric (SBWT-1000/1500) gorelockers.

How is a round duct elbow made?

From gores — ring segments cut at an angle, rolled round, and joined gore-to-gore on a gorelocker with a mechanical lock seam. A 90° elbow commonly uses three to five gores; more gores give a smoother sweep and lower pressure loss.

Can gorelockers run stainless steel?

Yes — SBEM-1250 to 1.0 mm, SBWT-1000 (SS304) to 0.8 mm, SBWT-1500 (SS304) to 1.2 mm. Galvanised, black steel and aluminium run to heavier gauges on the same machines.

Hydraulic or electric gorelocker — which one?

The hydraulic Gorelocker SBEM-1250 forms at up to 120 m/min, covers Φ100–Φ1250 mm, takes galvanised, black and aluminium sheet at 0.4–1.5 mm and stainless at 0.4–1.0 mm, and rolls a 5, 7.5 or 10 mm flange. The electric SBWT series runs frequency-controlled at up to 75 r/min: the SBWT-1000 covers Φ120–Φ1000 mm (galvanised 0.4–1.2 mm), the SBWT-1500 covers Φ120–Φ1500 mm (galvanised 0.4–1.5 mm, stainless SS304 0.4–1.2 mm). Pick by your largest elbow diameter and heaviest gauge.

What is the difference between the SBWT A and D variants?

Each electric Gorelocker comes in two variants: the A model forms the male and female edges of the gore joint, while the D model adds the seam-lock closing function (Male/Female/Seam Lock) with a second drive — 1.5 kW×2 + 2.2 kW×2 on the SBWT-1000D and 2.2 kW×2 + 2.2 kW×2 on the SBWT-1500D.

What does the Fitting Shaper do?

The Fitting Shaper SBJQJ-500 forms the ends of small-diameter round fittings — elbows, tees, reducers and branches from Φ90 to Φ400 mm — in galvanised steel, stainless steel and aluminium, with a 3.5 kW drive on a 380 V three-phase supply. It is the companion machine to the gorelockers for the small-fitting end of the range.

12-hour reply

Sizing a gorelocker against your elbow range and gauges? Ryan Tao replies within 12 hours.

Ask an engineer

Engineer reply

Ask an engineer about this guide

Describe your job and what you are trying to make. Ryan Tao replies within 12 hours.

Guide: Duct Elbow Machines: How Round Elbows Are Made, and the Gorelocker Specs (2026)

Not ready for a quote? Get the 2026 catalogue by email: 66 machines, one page each.

Machinery for this application

Elbow and fitting production runs alongside standard Taokron equipment: spiral tubeformers for the straight round duct, auto duct production lines for rectangular duct, and duct welding machines where welded fittings are specified — or browse the full machine catalog.