Flat sheet, flat parts, patterned plate
Leveling, Embossing and Cut-to-Length Machines
Precision levelers for sheet, cut parts and heavy plate, checker plate and decorative embossing machines, coil embossing lines, cut-to-length lines and embossing rolls. Each machine is configured to your material, thickness and width.
Overview
A leveler bends sheet or plate up and down through a row of rolls with less force at each roll, until the stress inside the metal evens out and it lies flat. An embossing machine presses a pattern into the surface between engraved rolls. A cut-to-length line uncoils, levels and cuts coil into flat sheets.
Taokron supplies HVAC duct machinery, roll forming lines and now these leveling and embossing machines. Ryan Tao in Melbourne is your contact from the first question to after-sales. Specifications on each page come from our machine catalogue. Where the catalogue gives no figure, or two different ones, we say so and confirm it on the quotation.
Levelers
6-High Precision Leveler
Mark-free leveling for stainless, aluminium and copper, 0.3 to 6 mm
Thin-Sheet Precision Leveler
4-high leveler for thin blanks and parts, up to 2000 mm wide
Heavy Plate Hydraulic Leveler
Thick and hot-rolled plate with scale or rust, up to 5200 mm wide
Part Leveler 0.5-30 mm
Flattens laser, flame-cut and stamped parts, 0.5 to 30 mm
Embossing machines
Checker Plate Embossing and Leveling Machine
Embosses tread plate and flattens it in one pass, up to 2500 mm wide
Heavy Hydraulic Checker Plate Embosser
Deep tread pattern on thick plate, hydraulic, 3 to 16 mm
Metal Sheet Embossing Machine
Decorative and anti-slip patterns with quick roll change, 1600 mm
Quick-Change Embossing Machines
Swap pattern modules without tools: 2-high for plate, 4-high for thin sheet
Coil lines
Appliance Panel Embossing Line
Coil embossing for fridge, freezer and washer panels, 0.2 to 1.2 mm
Heat Shield Embossing Line
Double-sided embossing of aluminium and stainless heat shield coil
Cut-to-Length Line
Uncoil, level, cut and stack, 1600 mm coil, plus or minus 0.5 mm
Rolls
Specifications at a glance
Factory figures. Open a machine for the full table.
| Machine | Thickness | Width | Speed |
|---|---|---|---|
| 6-High Precision Leveler | 0.3 to 6.0 mm | Custom | Stepless |
| Thin-Sheet Precision Leveler | 0.1 to 6 mm | Up to 2000 mm | 0 to 10 m/min |
| Part Leveler 0.5-30 mm | 0.5 to 30 mm | Up to 3000 mm | 0 to 10 m/min |
| Heavy Plate Hydraulic Leveler | 5 to 200 mm | Up to 5200 mm | Per site |
| Checker Plate Embossing and Leveling Machine | 0.2 to 16 mm | Up to 2500 mm | 0 to 10 m/min |
| Heavy Hydraulic Checker Plate Embosser | 3 to 16 mm | 1600 mm | To order |
| Metal Sheet Embossing Machine | 0.2 to 16 mm | 1600 mm | To order |
| Quick-Change Embossing Machines | On request | On request | On request |
| Appliance Panel Embossing Line | 0.2 to 1.2 mm | 1250 to 1500 mm | 0 to 30 m/min |
| Heat Shield Embossing Line | 0.3 to 1.0 mm | On request | 5 to 25 m/min |
| Cut-to-Length Line | 0.5 to 6.0 mm | Up to 1600 mm | 0 to 40 m/min |
How an order works
- You send the material and grade, thickness range, width, part or coil size, output and site power supply. For embossing, a photo or sample of the pattern.
- We send back a configuration, lead time and price.
- After the order and deposit, the machine is built to your configuration. Production for a standard machine is 60 to 120 days; custom rolls or a complete line take longer.
- The machine ships by container. Remote support included; on-site installation engineer available on request, quoted per order. Standard warranty is 12 months.
Supply terms
Who supplies it. Taokron. We handle the inquiry, specification review, quotation, pre-shipment inspection, shipping and after-sales support from Melbourne.
Lead time. Production time for a standard machine is 60 to 120 days. Custom rolls, a one-piece cast base, special roller sets or a complete line take longer. The exact time is confirmed at quotation.
Warranty. 12-month standard warranty on the machine.
Commissioning. Remote support included; on-site installation engineer available on request, quoted per order.
CE. The catalogue lists most of these machines as CE marked; each machine page says which. CE documents are sent with the quotation on request.
Price. Each machine is configured to your material, thickness and width, so there is no list price. Send your details and we quote that machine.
Buyer guide: why flat parts matter after laser and plasma cutting, and which leveler to buy →
Frequently asked questions
Who supplies these machines?
Taokron supplies them as part of its range. From Melbourne we handle inquiries, specification review, quotation, pre-shipment inspection, shipping and after-sales support, so you have one contact from the first question to commissioning.
Which leveler do I need?
For thin sheet with a finished surface, the 6-high precision leveler. For thin laser and punched blanks on a budget, the thin-sheet leveler. For cut and stamped parts up to 30 mm, the part leveler. For thick and hot-rolled plate, the heavy plate leveler. Send your parts and we confirm.
Can you make my embossing pattern?
Yes. Pattern rolls are engraved from your drawing or a sample sheet, for the embossing machines and as separate rolls.
How long does it take?
Production for a standard machine is 60 to 120 days; custom rolls, a cast base or a complete line take longer. The exact time is confirmed at quotation.
What warranty do I get?
12 months standard warranty.
Why are there no prices on the site?
Each machine is configured to the material, thickness, width and output. Send your details and we quote that machine within 12 hours.
Price request
Ask for a quotation on this machine
Send your material, thickness range, width and what the parts or sheets are for. Ryan Tao replies within 12 hours with a configuration, lead time and price. You can also send photos and drawings on WhatsApp +61 435 074 994.
Quotation for: Leveling or embossing machine
Several machines or a complete line? Use the full inquiry form