Insights · Welding

Round Duct Rolling and Welding Line: What to Check Before You Buy

When welded round duct beats spiral, what a plate-rolling, seam-welding and flanging line consists of, and the points to check on diameter, thickness, welding, leak testing, flanging, changeover, floor space and power before you order.

Who this guide is for

This guide is for duct shops, ventilation, dust-extraction and industrial fan makers, and steel fabricators who make large-diameter or heavy-gauge welded round duct and want a plate-rolling, longitudinal seam welding, circumferential seam welding and flanging set-up. It lists what to check before you order.

When welded round duct beats spiral

Spiral lockseam duct is the faster and cheaper way to make ordinary round duct for supply and return air. Our guide on spiral lockseam vs welded round duct compares the two in detail. Welded round duct earns its place in these cases.

  • Large diameter. Plate is rolled to the diameter you need, so you are not limited by the width of a spiral strip. The large round duct flange and seam welder lists diameters of 300 to 2000 mm, and 3500 mm at the limit.
  • Heavy gauge. Dust extraction and fan casings often use plate a spiral former does not roll. Our line lists 1 to 3 mm, the hydraulic four-roll machine rolls carbon steel up to 6 mm, and the large-duct welder lists up to 10 mm.
  • Pressure and airtightness. A continuous weld closes the seam without relying on a sealant, which matters for higher-pressure and gas-tight service. Pressure classes are explained in our duct pressure classes guide, and leakage classes in the air leakage classes guide.
  • Stainless and black steel. Stainless exhaust duct and carbon steel duct that is painted or lined later is normally welded. See galvanized vs stainless steel duct.

Welded duct costs more per metre, because each section is rolled and then welded separately. For thin galvanized sheet at ordinary pressure, spiral is cheaper. For spiral, see the SBTF-1602 spiral tubeformer.

What a rolling and welding line consists of

A rolling and welding set-up has up to four stations.

If you want the first stations as one sequence, the Round Duct Rolling and Welding Line takes steel from the coil: decoiling, leveling, cutting, four-roll rolling and seam welding. It has two layouts. The compact line rolls and welds cylinders up to 1500 mm long. The longer laser layout adds a 2 kW laser cutting station before the rolling machine, so holes and openings are cut in the flat blank. It ends at rolling and unloading, and the seams are welded on a separate seam welder.

Fittings are a separate question. Segmented elbow welding machines weld the joints of segmented elbows from 200 to 800 mm in diameter, and pipe flange and tee welding machines cover DN50 to DN600 pipe work. For long steel supports and brackets, see the gantry and support welding robots.

1. Diameter range

The compact line lists 400 to 1500 mm and the laser layout 300 to 1500 mm. The vertical straight seam welder lists round duct from 250 to 1600 mm, and the large-duct flange and seam welder 300 to 2000 mm. The hydraulic four-roll model lists a minimum diameter at full load of 300 mm, so check the smallest diameter at your thickest plate.

2. Thickness range

Thickness decides the rolling machine, the welding process and the power you need. The line lists 1 to 3 mm. The hydraulic four-roll machine lists carbon steel 6 mm and stainless 3 mm at up to 1500 mm wide, and the full-servo model covers thin sheet at 0.5 to 1.5 mm. The straight seam welder lists 1.0 to 3.0 mm for round duct. The rolling section is rated for sheet of 245 MPa yield strength or more, so give us your grade.

Be clear about the heavy end: the straight seam welder page does not list seams above 3.0 mm, so if your jobs run above that, say so and we confirm each station.

3. Length per section

The compact line lists cylinder lengths of 400 to 1500 mm, and the straight seam welder lists a weld length of 1500 mm. The large-duct flange and seam welder takes sections of 1200 to 4500 mm. The flanging machine lists a product height of 200 to 1450 mm, so check each station, not only the roller. Long sections also need a crane or hoist.

4. Material

The compact line lists stainless steel and carbon steel, and the laser layout adds galvanized sheet. The straight seam welder lists stainless, carbon steel and galvanized sheet. Galvanized steel can be welded, but the zinc burns off and needs fume extraction and a clean-up of the weld area afterwards, so confirm your customer accepts a welded galvanized seam. For stainless, internal and external gas shielding gives a cleaner weld.

5. Welding process

TIG, MIG/MAG, laser and resistance suit different jobs, and our guide to welding methods in HVAC duct fabrication compares them. In short, TIG is slower and cleaner and suits stainless and thin sheet. MIG/MAG is faster and suits carbon steel and thicker material. The straight seam welder lists TIG or MIG/MAG at 3 to 8 mm/s. The line page leaves the process to be agreed at quotation, so decide with us which one your material and finish call for.

6. Edge preparation and fit-up

A welded seam is only as good as the fit-up. Check how the machine holds the two edges together: the copper backing bar and clamping on the straight seam welder, and the tack welds and joint gap that the ring-seam welder asks for. It lists tack welds about 3 mm long every 50 mm and a joint gap of 0.5 to 1 mm. Cut edges need to be square and clean, because a rough edge leaves a gap that no welder closes well. The hydraulic four-roll machine lists a remaining flat after pre-bending of up to 1.5 x plate thickness, and a shorter flat gives a rounder cylinder.

7. Seam quality and leak testing

Agree the acceptance test before you buy, not after. For ventilation duct, EN 12237 specifies requirements and test methods for the strength and air leakage of circular sheet metal ducts. SMACNA publishes round industrial duct construction standards that include longitudinal welded seams. Practical checks on a welded section:

  • Visual inspection of every seam for undercut, burn-through, porosity and incomplete fusion.
  • A leakage test: close the ends of a section, pressurise it to the specified pressure and measure the airflow needed to hold it, then compare with the leakage class in your specification.

Ask what sample welding is possible in your material and thickness.

8. Flange attachment

There are two common ways to put a flange on a welded round duct. You can weld an angle or flat-bar ring to the end of the cylinder, which suits large diameters and heavy plate, and which the flange welder does. You can form the flange from the cylinder wall, which our flanging and punching machine does: 30 to 50 mm wide, stainless steel 0.8 to 3 mm and carbon steel up to 5 mm, on cylinders 400 to 1500 mm. Check what your duct standard calls for, and decide the gasket or sealant at the same time, because the flanged joint is where leakage often starts.

9. Fixturing and changeover

Changing diameter is where a line gives back the time it saved. On the vertical straight seam welder, switching between round and square duct is done at the touch screen, without changing the clamping fixture or the copper backing bar. Ask each station how long a change takes between your smallest and largest diameter, and whether it needs tools or a trial piece.

10. Floor space, power and operators

The compact line is listed at 13016 x 8084 x 4300 mm and the laser layout at 19000 x 5200 x 3000 mm. The vertical straight seam welder is 1900 x 1930 x 2810 mm and the large-duct flange and seam welder is 6900 x 4300 x 3400 mm. Add room for stock, finished sections and a crane or forklift route. Total rated power is 25 kW on the compact line, 15 kW on the straight seam welder, 48 kW on the large-duct welder and 14 kW on the flanging machine, which is listed at 380 V, 50 Hz, three phase. Send us your site voltage and frequency, and plan welding fume extraction.

On the compact layout the operator sets the job, and feeding, rolling, welding and discharge run as one sequence. Commissioning is by remote support, with an on-site installation engineer available on request, quoted per order.

Mistakes to avoid

  • Buying a rolling machine for the thickest plate and a welder for the thinnest, so that no station fits your real work.
  • Leaving the flange to last, when it decides the length, the gasket and the leakage result.
  • Not agreeing the acceptance test, such as the leakage class, in advance.

What we need from you to quote

  • Material and grade, and thickness range
  • Smallest and largest diameter, and the section length
  • Weld finish and any test you must meet
  • Daily output, site power supply and floor space

Send your duct sizes and material for a quote in 12 hours →

Taokron supplies these machines. Taokron (Melbourne) handles inquiry, specification review, quotation, pre-shipment inspection, shipping and after-sales support. Catalogue figures are confirmed on the quotation for your parts.

FAQ

Is welded round duct airtight without sealant?

A continuous, sound weld closes the seam by itself, so a longitudinal weld needs no sealant. The joints between sections still do: a flange needs a gasket or sealant. Test a finished section against the leakage class you need.

What thickness can the Taokron line roll and weld?

The Round Duct Rolling and Welding Line lists 1 to 3 mm, in stainless steel and carbon steel, with galvanized sheet on the laser layout. For thicker plate, the hydraulic four-roll machine rolls carbon steel up to 6 mm and stainless up to 3 mm, 1500 mm wide, and the large round duct flange and seam welder lists 1.0 to 10 mm. The straight seam welder on our site is listed at 1.0 to 3.0 mm for round duct, so tell us if your seams are thicker and we confirm the set-up on the quotation.

Which welding process should I choose, TIG or MIG?

TIG gives the cleaner weld on stainless and thin sheet and is slower. MIG/MAG is faster and suits carbon steel and thicker material. The vertical straight seam welder is listed with TIG or MIG/MAG, and the double-torch circumferential welder takes a wire feeder as an option. Choose by material, thickness and the weld finish your customer asks for.

Can I make flanged duct without welding angle rings?

For many round ducts and casings, yes. The Cylinder Flanging and Punching Machine turns a 30 to 50 mm flange from the cylinder wall and punches the bolt holes in the same set-up, on cylinders 400 to 1500 mm in diameter. Check your duct standard if it calls for a separate ring.

What do I need to send for a quotation?

Material and grade, thickness range, smallest and largest diameter, section length, the seams you weld (longitudinal, circumferential, flange), the weld finish required, daily output, site power supply and floor space, and your destination port.

12-hour reply

Send your duct sizes, material and thickness range. Ryan Tao replies within 12 hours with a configuration, lead time and price.

Ask an engineer

Engineer reply

Ask an engineer about this guide

Describe your job and what you are trying to make. Ryan Tao replies within 12 hours.

Guide: Round Duct Rolling and Welding Line: What to Check Before You Buy