Insights · Buyer guide

When to move from single machines to an auto duct line: 8 signs your shop is ready

If your rectangular duct is made on a shear, a folder, a lockformer and a TDF machine, you already know the routine. This guide is about the point where that routine starts costing more than it should. It lists eight signs that a coil-fed auto duct line deserves a serious look, what changes in the shop when one arrives, the step path from single machines to a full line, and the cases where waiting is the right call. The payback maths lives in separate guides, linked below.

The 8 signs your shop is ready

None of these is a reason on its own. Together they describe a shop where single machines have become the limit.

1. Offcuts from flat sheets keep piling up

Single-machine shops usually start from cut sheets. A coil-fed line cuts each panel to the length of the job from a continuous strip, so waste is the tail of a coil rather than the edge of every sheet. Coil is often cheaper per usable kilogram than cut sheet, but not always: compare mill quotes for both in your gauge, and ask what gauge tolerance the coil is supplied to, because billed weight and usable area are not the same thing.

2. Everything queues at the folder

If the shear is waiting for the folder, or the folder is waiting for the lockformer, you are balancing four machines by hand every day. The SBAL-III puts hydraulic notching, square punching, shearing and folding on one line with closed-loop servo control, so the sequence stops depending on who is free.

3. Overtime has become the schedule

Occasional overtime is normal. Overtime every week to hit delivery dates means the shop is running at its ceiling. Check whether the extra hours go on straight duct, which a line takes over, or on fittings, which it does not.

4. Skilled fabricators are hard to hire and keep

The Taokron product pages describe the SBAL family as a coil-to-duct line run by two to three people, replacing what was six to eight stations and eight to twelve operators in a traditional shop. The SBAL-V is designed to be run by one trained operator under normal conditions. Your own numbers will differ, but the direction matters if you cannot fill the benches you already have. The labour side is covered in duct shop labour and throughput economics.

5. The same sizes repeat on big projects

Hospitals, airports, shopping centres and large commercial towers are the projects the product pages name for these lines, and the common thread is long runs of repeating sizes. Entering a size on the PLC touchscreen is quick; the pages quote a changeover under one minute. A shop that mostly makes one-off shapes gets less from that.

6. Consistency has started to matter

Tight tenders ask for duct that goes together square and tests well. Machine-cut length and squareness are only part of leakage performance, since seams, corners and sealant matter too, but cutting and folding are the part a line controls. The SBAL-III page lists length tolerance of ±0.5 mm and diagonal of ±0.8 mm. For the standards side, see duct air leakage classes explained.

7. Sheet stacks are eating the floor

Cut sheets in stacks, part-finished duct on trolleys and four machines spread around the shop use a lot of space. A line needs its own footprint, but it replaces the stacks with a decoiler and coil rack. The Line II and SBAL-III mainframes are about 1.9 to 2.3 m long with a separate decoiler, and the SBAL-V is 14.5 m long in a U-shape. See HVAC duct factory layout before you commit to a position.

8. Quotes take too long, or jobs get turned down

When you cannot promise a delivery date without checking the folder queue, or you decline a job because the shop cannot take it, capacity is costing you work. That is a different problem from cost per square metre, and it often shows up before the labour numbers do.

As a rough guide, if three or four of these describe a normal month, ask for a sizing. If one or two do, a single extra machine may be the cheaper fix.

What changes in the shop

  • Coil storage and handling. Line II and the SBAL-III list a maximum coil weight capacity of 8,000 kg on the decoiler. You need a crane or forklift rated for your coils and a clear route from the door to the decoiler.
  • Power. The three lines are listed at 380 V, 50 Hz, 3-phase, with 9.2 kW (Line II), 10.7 kW (SBAL-III) and 40 kW (SBAL-V) connected. Your electrician should size the feeder from the electrical schedule; the power and electrical requirements guide explains how.
  • Layout. Material should move one way, coil in and finished duct out, with somewhere for the duct to land. The factory layout guide covers zones and clearances.
  • Operators. The work shifts from cutting and folding to loading coil, entering sizes, checking the first piece and moving finished duct. The product pages say operator training is part of the on-site commissioning visit, quoted per engineer-day.
  • Downstream machines. The lockformer, TDF machine, zipper and corner machine do not disappear. They get fed by the line instead of by a folder.

The step path: single machines to a full line

The table below follows how the product pages position each step. It is a map, not a rule. You can go straight to the SBAL-III or SBAL-V if your volume is already there.

StepWhat you runFrom the product pages
0. Single machinesShear, folder, lockformer, TDF flange machine, optionally a duct zipperPneumatic folder 0.4–1.5 mm (1,500 mm model); lockformer Pittsburgh 0.4–1.2 mm; SBTDF-12 0.5–1.2 mm and SBTDF-1.5-16 0.8–1.5 mm; zipper SBHF-1.5×1500TDF 0.8–1.5 mm
1. Rectangular Duct Line IIEntry-level coil-fed line for shearing, notching, beading and folding; TDC or TDF formed downstreamSBAL-II-1250 / 1550; 0.5–2.0 mm; 18 m/min; 9.2 kW; 3,000 / 3,500 kg
2. SBAL-IIIHydraulic notching, square punching, shearing and folding with closed-loop servo; TDF or angle flange with downstream equipmentSBAL-III-1250 / 1550; 0.5–2.0 mm; 18 m/min feeding; 10.7 kW; 3,250 / 4,000 kg
3. SBAL-VU-shape line for high-volume work; Pittsburgh lock and TDF or angle flange formed inlineSBAL-V-1250U / 1550U; 0.5–1.5 mm; 18 m/min; 40 kW; about 16 tons; 14,500 mm long

Two points on that ordering. Gauge: if you regularly run above 1.5 mm, the SBAL-V is not the fit and the Line II or SBAL-III is. And your single machines stay useful at every step, so the step is an addition more than a replacement. The detail on the top two lines is in SBAL-V vs SBAL-III and the three-way auto duct line comparison; the selection method is in how to choose an auto duct line.

When not to buy a line yet

  • Most of your work is fittings and one-off shapes. A line makes straight duct. A good folder and a cutting machine such as the plasma cutter (0.4–4 mm) will do more for you.
  • Volume is uneven or unproven. A line needs steady straight-duct work to stay busy. If one large job is carrying the forecast, wait for the pipeline to confirm it.
  • The bottleneck is one machine. If only the closure step is slow, a TDF machine or zipper may fix it for far less than a line.
  • The building is not ready. No three-phase supply, no way to lift a coil, or no clear floor length means site work first.
  • You cannot buy coil in your gauge. Check your supplier before you check the line.

For the money side, use the duct machine ROI and payback calculator and the worked examples in auto duct line ROI and cost analysis.

What to send us to size a line

The product pages ask for the same list, and it takes ten minutes to write:

  • Output in square metres per month, and the target per shift, not a theoretical peak
  • Material and gauge range
  • Closure: TDF, TDC or Pittsburgh
  • Smallest and largest duct sizes, and how much of the work is small duct
  • Power supply, and your available floor length and ceiling height
  • How coil gets lifted and moved today

Taokron has built duct machines since 1994, with machines running in 100+ countries and 60+ patents behind the designs. A reply with those six items gets you a line recommendation from an engineer, including the option of not buying one yet. For a real installation, see the Australian duct shop case study.

Send your shop details and get a line sizing in 12 hours →

FAQ

How do I know my shop is ready for an auto duct line?

Look for a pattern, not a single bad week. Regular overtime, a folder that everything queues behind, offcuts from cutting flat sheets, repeat sizes on large projects and jobs you slow down or turn away because of shop capacity are the usual signals. If three or four of the eight signs in this guide describe your normal month, request a sizing from Taokron with your monthly square metres, gauge range and closure type.

Can I keep my shear, folder, lockformer and TDF machine after buying a line?

Yes, and most shops do. A line makes straight rectangular duct from coil, so the folder is still needed for transitions, offsets and short runs, and a lockformer or TDF machine stays useful on a line that does not form closures inline. The Rectangular Duct Line II works with TDC or TDF flange forming downstream, the SBAL-III with TDF or angle flange forming downstream, while the SBAL-V forms TDF or angle flange and Pittsburgh lock inline.

Which line should a first-time buyer look at: Line II, SBAL-III or SBAL-V?

The product pages position the Rectangular Duct Line II as the entry-level line, the SBAL-III as the line with hydraulic notching, punching, shearing and folding for medium volumes, and the SBAL-V as the U-shape line for high-volume work. One practical difference is gauge: Line II and SBAL-III run 0.5-2.0 mm, while the SBAL-V runs 0.5-1.5 mm. Your gauge range and monthly square metres decide the answer.

What does an auto duct line need from the building?

A three-phase supply (the Taokron lines are listed at 380 V, 50 Hz, 3-phase), floor space for the line and its decoiler, a way to lift and load coils, and room to stage finished duct. Connected power is listed as 9.2 kW for Line II, 10.7 kW for the SBAL-III and 40 kW for the SBAL-V. Confirm the final cable and breaker sizing against the electrical schedule for your model.

Is an auto duct line worth it if I make a lot of fittings and custom shapes?

Usually not on its own. A coil-fed line is built for straight rectangular duct in repeating sizes. If most of your output is fittings, transitions and one-off shapes, a folder and a cutting machine such as a plasma cutter will do more for you, and a line makes sense once straight duct is a large share of the work.

What should I send Taokron so a line can be sized?

Send your monthly or per-shift output in square metres, your material and gauge range, whether you form TDF, TDC or Pittsburgh closures, your largest and smallest duct sizes, your power supply and your available floor length. A photo or sketch of the shop helps. A Taokron engineer replies within 12 hours.

Duct Shop Notes

One email a month for duct shop owners

Notes on machine choices, shop layout, duct standards and new machines. Reply "unsubscribe" any time to stop.

12-hour reply

Wondering if your shop is ready for a coil-fed line? Send your monthly square metres, gauge range and closure type and a Taokron engineer will reply within 12 hours with a straight recommendation, including when to wait.

Ask an engineer

Engineer reply

Ask an engineer about this guide

Describe your job and what you are trying to make. Ryan Tao replies within 12 hours.

Guide: When to move from single machines to an auto duct line: 8 signs your shop is ready

Not ready for a quote? Get the 2026 catalogue by email: 66 machines, one page each.

Machinery for this decision

The step path above runs on auto duct production lines and TDF flange and lockformer machines, or browse the full machine catalog.