Insights · Market guide

HVAC Duct Fabrication in Venezuela 2026: Market, Standards and Machines

Venezuela in 2026 is a rebuilding market in a hard operating environment. This guide is for duct shop owners and HVAC contractors there who are deciding whether to add capacity or automate. It sets out what is documented about demand after the June 2026 earthquakes, which standards apply, the import and payment questions to settle before you order a machine, the 60 Hz power supply, and the machine set-ups that fit. Where we could not verify a fact, we say so.

Also in: Español

Why Venezuela in 2026

Facts about Venezuela change quickly and sources do not always agree. This section keeps to what is documented, gives the source, and says where a number is an estimate.

The starting point

In January 2026 Venezuela's National Assembly approved a partial reform of the hydrocarbons law that lets private companies operate upstream oil projects under new contracts. Independent estimates put oil output at roughly 1.1 million barrels a day in mid-2026, and the figures vary by source. US sanctions have eased in steps through OFAC general licences, first for the oil sector and later for some other activities. They have not been lifted as a whole, and licences can change. Inflation is still very high: the IMF's October 2026 outlook, as reported, projects an average of about 468% for 2026.

Rebuilding after the June 2026 earthquakes

Twin earthquakes of magnitude 7.2 and 7.5 struck on 24 June 2026. In July the World Bank estimated direct physical damage at US$19.6 billion: 47% residential buildings, 27% infrastructure and 26% non-residential buildings. La Guaira state and the Capital District, which includes Caracas, account for about half of the total. The World Bank also said that at current investment levels, reconstruction would remain incomplete over ten years. After the quakes the Colegio de Ingenieros de Venezuela called for an update of the seismic code.

For a duct shop this means repair and fit-out work in damaged buildings. The pace depends on financing, so do not assume a boom. Plan for steady, project-by-project work.

Hospitals

The Pan American Health Organization said in July 2026 that 38 of the 73 health facilities it had assessed after the quakes reported earthquake-related damage, and that three remained non-operational. Counts were preliminary and the assessment was continuing. The government announced a US$200 million fund for hospitals and homes. Operating theatres, isolation rooms and laboratories need tightly sealed ductwork, often in stainless steel. See our cleanroom duct guide and galvanised vs stainless comparison.

Oil, industry, food and commercial refurbishment

  • Oil and gas: new contracts and licences are drawing investment plans for fields and facilities. Offices, control rooms, workshops and camps need ventilation, but we could not find reliable duct volumes for the sector.
  • Food processing and cold storage: these plants need ducted ventilation, make-up air and clean areas. We found no verified project list, so we name none.
  • Commercial refurbishment in Caracas: offices, shops and hotels needing repair or new air conditioning are the everyday work of most duct shops. Again, we do not name projects we could not verify.
  • Construction outlook: the president of the Cámara Venezolana de la Construcción has said he expected the last quarter of 2026 to be more active, and tied recovery to a stable electricity system and higher oil output. He named electricity and drinking water as the most urgent needs.

Standards and codes for ductwork in Venezuela

We could not find a Venezuelan standard for sheet metal duct construction. In practice the mechanical engineer's specification decides what you build to.

  • SMACNA HVAC Duct Construction Standards: often named in specifications from international consultants for gauges, seams, transverse joints, reinforcement and hangers. We could not confirm that it is a national requirement. See our gauge chart and hangers and supports guide.
  • ASHRAE: Venezuelan HVAC design work commonly uses ASHRAE methods for loads and ventilation. These drive airflows and duct sizes, not construction details.
  • COVENIN 1756-1:2019: the seismic design standard for buildings, which replaced the 2001 edition. After the June 2026 earthquakes, hanger and bracing details are worth checking against the project documents. Ask the engineer whether non-structural elements such as ducts need seismic restraint.
  • Fondonorma 200:2009: the Código Eléctrico Nacional, for electrical installations. It applies to your workshop supply and wiring.
  • Sanitary rules for buildings: Venezuelan design work also refers to national sanitary norms for buildings. Ask the project engineer which documents apply to a health or food project.

Our international duct standards guide compares the main systems.

Importing duct machinery into Venezuela

  • Customs and broker: customs is run by SENIAT. Use a licensed customs broker from the start, and ask for the tariff line and all charges in writing before you order.
  • IVA: the standard rate is 16% and it applies at import. Ask your broker how the taxable base is set.
  • Customs duty: the rate depends on the tariff line. Machines of this kind usually fall under HS 8462/8463, so confirm with your broker. We do not quote a duty figure.
  • Capital goods exemptions: rules have changed several times. A customs tariff amendment (Decree 5,198, in force from 5 January 2026) reportedly lets the VAT exemption for capital goods be combined with an exemption certificate from the trade authority, COMEX. Ask your broker whether your company qualifies.
  • Payment routes and sanctions: confirm with your bank how it will process an international transfer to a supplier, and how long it takes. US sanctions on Venezuela have eased in steps but remain in force in many areas, and OFAC licences can change, so check the current position with your bank or adviser. This guide is not legal advice.
  • Exchange rate: the official rate has moved fast in 2026 and secondary sources differ on the current level. Agree the currency and price terms clearly in the contract, and ask your bank how it will convert.

Tell us your preferred port when you request a quotation, and confirm that the port and the road to your workshop are working normally, because La Guaira state was in the earthquake zone. Our importing guide covers the general paperwork.

Power supply: 60 Hz, and specify the voltage at order

Venezuela's grid runs at 60 Hz. Single phase supply is 120 V. Three phase supply depends on the building: 208 V, 240 V and 480 V systems are all used, and 480 V is common in industrial sites. The standard specification on our product pages is 380 V, 50 Hz, three phase. That is why the voltage must be fixed at order. Motors, drives and the control transformer are built for one voltage and frequency, and a mismatch causes wrong speed, overheating and damage.

Measure the three phase voltage at your workshop and give it to us, together with the supply frequency. We build the machine to match. Because the construction chamber names electricity as a pressing national need, also ask your electrician about voltage stability, and consider a stabiliser or a generator sized to the machine power. See also duct machine voltage and frequency by country.

Typical Venezuelan shop set-ups and the machines that fit

Contractor shop, rectangular duct for fit-outs and repairs

A practical set is a Rectangular Duct Line II SBAL-II or Auto Duct Line SBAL-III, both for 0.5 to 2.0 mm sheet in 1250 or 1550 mm widths at a feeding speed up to 18 m/min. Add a Pittsburgh lockformer (SBLC series), which handles 0.4 to 1.2 mm for the Pittsburgh lock and 0.7 to 1.5 mm for snap lock, and a TDF flange forming machine (SBTDF), available for 0.5 to 1.2 mm or 0.8 to 1.5 mm. A pneumatic folder (SBWS) finishes fittings and bends. This covers straight duct, TDF joints and simple fittings with a small crew.

Larger rectangular shop for hospital, industrial and rebuilding packages

For volume, the Auto Duct Line SBAL-V runs 0.5 to 1.5 mm sheet in 1250 or 1550 mm widths at up to 18 m/min, and is rated at 40 kW. Close seams with the Duct Zipper SBHF-1.5x1500TDF, a double-sided closing machine for 0.8 to 1.5 mm sheet and duct lengths of 1000 to 1500 mm, or the lighter Seam Closing Machine SBHF-I for 0.5 to 1 mm. Corner parts come from the Auto Corner Making Machine and are fitted with the SBCC corner inserting machine, which handles sheet up to 1.5 mm. A hydraulic folder (SBWS-H) takes heavier gauges, up to 2.0 mm on the 1500 mm model, and the Plasma Cutter SBPC1550 cuts fittings from 0.4 to 4 mm sheet on a 1550 mm wide table, 4000 or 5000 mm long.

Round duct

Add spiral duct once round work is regular, for example in warehouses, car parks and industrial extract. The Spiral Tubeformer SBTF-1500 forms galvanised steel 0.4 to 1.2 mm in diameters from 80 to 1500 mm. The SBTF-1602 reaches 1600 mm and 1.3 mm galvanised, and the Spiral Duct Flanging Machine SBFB-1600 turns flanges on round duct ends. For a real example, see Kavanagh Industries in Sydney, which added an SBTF-1602 in October 2026.

Labour and space

We have no reliable wage data for Venezuelan sheet metal workers, so we give no figure. The case for automation is practical: an auto duct line replaces much of the manual marking, cutting, notching and folding, so a small crew can supply several sites, which matters if skilled staff are hard to find or keep.

On space, the auto duct line is the longest item, with coil racks at one end and a run-out table at the other. Ask us for a layout drawing based on your building before you commit to a site, and leave room for coil deliveries, finished duct storage and truck loading. Our factory layout guide has worked examples.

Working with Taokron from Venezuela

  • Machines built since 1994 and supplied to 100+ countries, with 60+ patents, from an ISO 9001:2015 factory
  • CE marked with a Declaration of Conformity
  • Built for your measured three phase voltage and 60 Hz supply
  • Installation and commissioning quoted per engineer-day
  • Replies within 12 hours by email at [email protected] or on WhatsApp at +61 435 074 994

Get a Venezuela-ready Taokron quotation →

FAQ

Which ductwork standards are used in Venezuela?

We could not find a Venezuelan COVENIN or Fondonorma standard for sheet metal ductwork, so the project specification decides. Engineers commonly design ventilation to ASHRAE, and specifications written by international consultants often name SMACNA for gauges, seams, joints and hangers. Around that sit national documents: COVENIN 1756-1:2019 for seismic design of buildings, and the Fondonorma 200:2009 National Electrical Code for the electrical installation. Always build to the documents named in your project specification.

What voltage and frequency do duct machines need in Venezuela?

Venezuela's grid runs at 60 Hz. Single phase supply is 120 V. Three phase supply depends on the building, and 208 V, 240 V and 480 V systems are all used. A machine built for another voltage or for 50 Hz will not run correctly, so measure the three phase voltage at your workshop and give it to us when you order. We then build the motors, drives and control transformer to match.

What taxes apply when importing duct machinery into Venezuela?

The standard IVA rate is 16% and it applies at import, so ask your broker how the taxable base is set. Customs duty depends on the tariff line, and machines of this kind usually fall under HS 8462/8463, so confirm the classification and rate with your broker. Exemptions for capital goods have changed several times in recent years, so ask your broker whether an exemption certificate applies to your company. We do not quote a duty figure here.

Can we pay for a machine from Venezuela while sanctions apply?

We cannot give legal advice on this. US sanctions on Venezuela have eased in steps through OFAC general licences since January 2026, but they have not been lifted as a whole and the rules can change. Before you sign, ask your bank how it will process an international transfer to a supplier, how long it takes and what paperwork it needs. Check the current OFAC position with your bank or adviser as well.

Where is ductwork demand in Venezuela coming from in 2026?

The documented drivers are rebuilding after the twin earthquakes of 24 June 2026, which the World Bank estimated caused US$19.6 billion of direct damage with about half in La Guaira and the Capital District, hospital repair, and work linked to the oil sector as new rules and licences open it to private operators. Commercial refurbishment, food processing and cold storage also need ductwork, but we could not verify specific projects, so we do not name any.

Which machines should a new Venezuelan duct shop start with?

A contractor shop making rectangular duct for offices, clinics and fit-outs usually starts with a rectangular duct line or auto duct line, a Pittsburgh lockformer, a TDF flange former and a folder. Add a seam closing machine, corner machines and a plasma table as volume grows, and a spiral tubeformer when round duct becomes regular work. Send your duct sizes, gauges and monthly output and a Taokron engineer will propose a machine set within 12 hours.

How should a Venezuelan shop prepare for power supply problems?

The Venezuelan construction chamber has named the electricity system as one of the most urgent needs in the country. Ask your electrician about voltage stability at your site. A stabiliser or a generator sized to the machine power may be worth the cost. For example, the Auto Duct Line SBAL-V is rated at 40 kW and the SBAL-III at 10.7 kW. Tell us your supply details and we will advise.

Sources: World Bank, July 2026 · PAHO, 24 July 2026 · Baker McKenzie, January 2026 · OFAC Venezuela-related sanctions · Fondonorma 200:2009 summary. Check current rules before you decide.

12-hour reply

Setting up or upgrading a duct shop in Venezuela? A Taokron engineer replies within 12 hours.

Ask an engineer

Engineer reply

Ask an engineer about this guide

Describe your job and what you are trying to make. Ryan Tao replies within 12 hours.

Guide: HVAC Duct Fabrication in Venezuela 2026: Market, Standards and Machines

Not ready for a quote? Get the 2026 catalogue by email: 66 machines, one page each.

Machinery for this application

The duct fabrication workflows above run on standard Taokron equipment: spiral tubeformers for round duct, auto duct production lines for rectangular duct, and TDF flange and lockformer machines for closure, or browse the full machine catalog.