Insights · Welding

Duct Flange Laser Welding Robot: Is It Worth It for Your Shop?

When a robot laser welding cell for duct flanges pays off against manual arc welding or a handheld laser, what to check on flanges, fixturing, safety, fume extraction and power, and a simple payback method built from your own figures.

Who this guide is for

This guide is for owners and production managers of rectangular duct shops who weld flanges to stainless or galvanized duct today, by hand or with a handheld laser, and are asking whether a robot cell is worth the money. It does not give a price, because the cell is configured to your parts. It gives you the questions to ask and a way to work out the answer from your own numbers.

One scope note first. The robot cell on our pages is for rectangular duct flanges. For round duct, the flange job is done by the circumferential seam and flange welders or by forming an integral flange on the CNC flanging and punching machine. Our guide to straight seam and circumferential seam welders covers that side.

What the cell does

A six-axis robot runs on a floor track beside two work stations. The operator places a duct section and its flange, a vision system scans the joint with a laser line, and the robot generates its own weld path and welds the flange to the duct by laser, both horizontal and vertical seams. While it welds on one station, the operator unloads and loads the other. No teaching is needed for each new size: the job is entered as parameters on the touch screen.

These are the catalogue figures from the robot laser welding cell page. Final figures depend on your parts and material and are confirmed on the quotation.

ItemListed figure
MaterialStainless steel, galvanized sheet
Thickness0.6 to 2 mm
Duct section200 x 200 to 1500 x 2000 mm, height up to 1250 mm
ProcessLaser welding with laser seam tracking
RobotSix-axis on a floor track (seventh axis, servo driven)
StationsTwo
Repeat positioning accuracy±0.05 mm
Total rated power16 kW, 380 V / 50 Hz
Cell size (L x W x H)5100 x 2100 x 3000 mm

Three ways to weld a flange to duct

The honest comparison is between three set-ups, and the right one depends on your volume and your people.

  • Manual arc welding (TIG or MIG). Cheapest to buy and the most flexible: any flange, any size, any odd job. Output and quality depend on the welder, and arc heat can distort thin sheet or burn through it. Our guide to welding methods in HVAC duct fabrication compares TIG and MIG in detail.
  • Handheld laser welding. The operator still guides the torch, so it stays flexible, but the heat input is lower than arc welding. Our handheld laser welding machine is listed with a 1064 nm wavelength and water cooling. It speeds up skilled work. It does not remove the dependence on the operator.
  • Robot laser cell. The vision system finds the seam and the robot runs the path, so the weld is the same on the first flange and the five hundredth. It costs the most and needs the most from your shop: floor space, safety guarding, fume extraction, and enough repeat work to keep it busy.

On heat, the direction is well documented. TWI states that laser welding has a low heat input compared with arc processes, because the beam is absorbed efficiently in the keyhole, and that it suits materials needing minimal thermal distortion. That matters on thin stainless and on galvanized coating. The size of the benefit depends on material, thickness and settings, so treat it as a reason to test your own parts, not as a number.

When a robot cell tends to pay off

  • Flange welding fills a large share of a welder's day, or of several welders' days, week after week.
  • You make many flanged sections of the same families, so the fixtures and parameters are reused.
  • Your quality complaints or rework hours come from flange welds: distortion, burn-through, uneven beads, grinding to clean up.
  • Skilled welders are hard to find or hard to keep, and the flange work is holding up the rest of the line.
  • You turn down or outsource work because flange welding is the bottleneck.

When it usually does not

  • Flange welding is occasional, or every job is different.
  • Most of your ducts are outside the listed size or thickness range.
  • You fasten angle flanges with fasteners instead of welding them. In that case the vision flange fastening machine is the related machine to look at, not a laser cell.
  • You cannot give the cell the floor space, power, extraction and guarding it needs.

A payback method that uses your own figures

We do not quote a payback period here, because it would be your numbers, not ours. Work it out in five steps on a sheet of paper.

  1. Measure today's cost. Over a normal month, count the flanged sections you weld, the welder hours spent on them (welding, fit-up, grinding, straightening and rework), and the consumables used: wire or filler, gas, tungsten, discs. Multiply hours by your loaded hourly cost.
  2. Estimate the cell's running cost for the same sections. Take the seam length per section and divide by the welding speed we confirm for your material. Add loading time, but note that with two stations loading overlaps with welding. Add the operator's time, power, consumables, maintenance and the extraction running cost.
  3. Work out the monthly saving. Monthly saving = today's monthly cost, minus the cell's monthly running cost, plus the margin on any extra work the freed capacity lets you take. Count the margin only if you have the orders or the quotes.
  4. Add up the full installed cost. Machine price, freight, any import costs in your country, installation, fume extraction, guarding and enclosure, electrical work, fixtures for your flanges, and operator training.
  5. Divide. Payback in months = installed cost divided by monthly saving. Then repeat the sum with half your volume, and with a smaller saving on rework. If it still works, the case is sound. If it only works at full volume, it is a risky case.

Send us the figures from step 1 and we help with step 2 for your parts, in the same quotation.

What to check before you buy

Flange types and sizes

Check your range against the listed duct section, 200 x 200 to 1500 x 2000 mm and up to 1250 mm high, and against the thickness range of 0.6 to 2 mm. Then check the flange itself. The product page lists fixtures for your flange profile as an option to discuss, and asks for the flange type and how it sits on the duct. Send a drawing or a photo of a finished joint so we can confirm the cell handles it.

Fixturing and changeover

On our page, no teaching is needed for each size: you enter the job as parameters and the vision system finds the joint. Ask what is left to change between families: fixtures, clamps, stops. Count how many changeovers you do in a normal week, because that decides how much of the saving survives.

Operator skill

A cell moves skill from the torch to the set-up and to the loading. The operator still has to position the section and flange correctly. Laser welding is sensitive to surface condition and needs precise positioning, while arc welding can bridge gaps better, so check how much gap and misalignment the cell tolerates on your joint. That figure is not on the product page, and we confirm it for your parts.

Safety: laser class and the robot cell

Laser products are classified from Class 1 to Class 4 under IEC 60825-1. Class 4 is the highest, and a Class 4 beam can burn skin and cause permanent eye damage. OSHA notes that Class 4 beams are hazardous to view even as diffuse reflections, and are a fire hazard. Most industrial lasers are safe in use because a higher-class laser sits inside an interlocked, labelled enclosure, and the machine counts as Class 1 in normal operation. That does not necessarily cover service work, when the beam may be accessible.

Ask any supplier for four things in writing: the class of the laser source, the class of the finished cell, how the guarding and interlocks work, and what the service procedure is. The robot cell is also covered by the robot safety standard ISO 10218-2, which covers integrating robots into a cell, including risk assessment, safeguarding and verification for the whole cell. Check with a laser safety adviser in your own country what else applies to your site.

Fume extraction

Laser welding is still welding. The International Agency for Research on Cancer has concluded that all welding fume can cause lung cancer, and the UK HSE says general ventilation does not achieve the necessary control, so welding indoors needs engineering controls, typically local exhaust ventilation. HSE links metal fume fever to welding galvanised metals, and stainless fume contains hexavalent chromium and nickel.

TWI advises capturing fume as close to the source as possible and having fixed extraction designed by competent professionals, not by the fabricator. Put the extraction in the cost of the project, and ask us where the extraction connects on the cell layout.

Power and cooling

The cell is listed at 16 kW total rated power on 380 V / 50 Hz. Check your site supply and the cable run to the cell position. The product page does not list how the laser source is cooled, so ask for the cooling arrangement and any chiller requirement on the quotation, and plan the space for it. Our handheld laser machine, for comparison, is listed with water cooling.

Floor space and layout

The cell footprint is listed at 5100 x 2100 x 3000 mm. Leave room around it for the guarding, for the extraction, and for moving finished sections out. Long flanged sections are awkward to carry, so plan the route from the cell to your next station.

Material and thickness

Stainless steel and galvanized sheet from 0.6 to 2 mm are listed. If your range includes thicker flanged duct, or aluminium or other materials, tell us before you plan around the cell. We confirm the welding speed for your material at quotation. The speed on the product page and the catalogue differ, so the speed for your material is a quoted figure to hold us to.

Weld quality and distortion

The repeat positioning accuracy is listed at ±0.05 mm. The way to settle quality is to send sample parts or drawings and ask for the weld on your own flange, material and thickness. Compare it with your current weld on distortion, appearance and the amount of cleaning you do afterwards. Check how the weld has to pass your customer's inspection or leakage test, because that decides whether the finish is enough as welded.

Throughput in terms of your own volumes

Do not buy on a catalogue speed alone. Count the flanged sections you weld in a shift, find the seam length of each, and divide by the confirmed welding speed. Then check the loading side: with two stations the operator loads one while the robot welds the other, so the cell stays busy only if the operator can keep pace. If your shift output is far below what one cell could weld, the right answer may be a handheld laser, not a robot.

What sits before and after the flange weld

Welding is one step in the flange job, so look at the steps around it. If you make angle flange frames, our angle steel punching line punches the rivet holes and slots and chamfers the corners, and the four gun angle iron flange welding machine welds the frames. If you want a robot for brackets and supports as well as flanges, see the gantry and support welding robots. The whole welding range is on the welding and cutting automation page.

Buying checklist

  • Write down your monthly flanged sections, welder hours and rework hours before you ask anyone for a price.
  • Check duct size, thickness and material against the listed range.
  • Send a drawing or photo of your flange and how it sits on the duct.
  • Ask for the laser class, the enclosure and interlock design, and the service procedure in writing.
  • Plan and cost fume extraction with a competent designer.
  • Check site power (380 V / 50 Hz listed), floor space and cooling.
  • Ask for a sample weld on your own parts and compare it with today's weld.
  • Run the payback sum at full and at half volume.

What we need from you to quote

  • Duct sizes, thickness and material
  • Flange type and how it sits on the duct (a drawing or photo)
  • Number of flanged sections per shift
  • Site power supply

Send your flange details for a quote in 12 hours →

Taokron supplies the cell and handles inquiry, specification review, quotation, pre-shipment inspection, shipping and after-sales support. Catalogue figures are confirmed on the quotation for your parts. We have built duct machinery for over 30 years, and our machines run in more than 100 countries.

FAQ

Is a robot laser welding cell worth it for a small duct shop?

It depends on how many flanged rectangular sections you weld, not on shop size. If flange welding is a few sections a week, a handheld laser or a good welder may be cheaper overall. If it fills a large share of a welder's day, or if rework and distortion cost you hours, the cell is worth pricing. Use the payback method above with your own figures.

What does the operator still do?

The operator places the duct section and flange, loads and unloads, and enters the job as parameters on the touch screen. The vision system finds the joint and the robot generates the weld path. With two stations, loading happens while the robot welds on the other one.

What duct sizes and materials does the cell take?

On our product page the cell is listed for stainless steel and galvanized sheet, 0.6 to 2 mm thick, in duct sections from 200 x 200 mm to 1500 x 2000 mm and up to 1250 mm high. It is for rectangular duct flanges. Anything outside those figures is confirmed on the quotation.

What safety measures does a laser welding cell need?

Lasers are classified from Class 1 to Class 4 under IEC 60825-1, and a higher-class industrial laser is made safe in use by enclosing the beam behind interlocked guarding. The cell as a whole also needs a risk assessment, safeguarding and verification under the robot safety standard ISO 10218-2, so ask your supplier which edition they work to. Ask any supplier for the laser class, the enclosure and interlock design, and the service procedure.

Does laser welding need fume extraction?

Yes. HSE states that all welding fume can cause lung cancer and expects engineering controls, typically local exhaust ventilation, for welding indoors. HSE links metal fume fever to welding galvanised metals, and stainless fume contains hexavalent chromium and nickel. Plan the extraction with a competent designer.

What do I send you to get a quotation?

Duct sizes, thickness and material, the flange type and how it sits on the duct (a drawing or photo), the number of flanged sections per shift, and your site power supply. A photo of how you weld the flange today helps us more than anything else.

Duct Shop Notes

One email a month for duct shop owners

Notes on machine choices, shop layout, duct standards and new machines. Reply "unsubscribe" any time to stop.

12-hour reply

Send your parts, material and thickness range. Ryan Tao replies within 12 hours with a configuration, lead time and price.

Ask an engineer

Engineer reply

Ask an engineer about this guide

Describe your job and what you are trying to make. Ryan Tao replies within 12 hours.

Guide: Duct Flange Laser Welding Robot: Is It Worth It for Your Shop?