Who this guide is for
This guide is for a buyer who is moving from buying cut sheet to buying coil, or from a hand-fed shear to a proper line. A cut-to-length line takes coil in at one end and puts flat, measured sheets on a stack at the other. The usual buyers are:
- Steel service centres that sell cut sheet by length and need the same length every time.
- Duct shops that buy galvanized coil and want to cut their own sheets, instead of paying a supplier to do it.
- Panel and appliance makers that feed presses and bending cells with blanks. The product page lists appliance shells, auto parts and heat shield blanks, building sheet, door and window parts, and machine housings among the typical uses.
- Laser and plasma shops that want to cut from leveled coil-fed blanks and not from stock sheet.
Coil is often cheaper per tonne than cut sheet, and a line gives you control of length and flatness. The cost is the line itself, the floor it needs and the coil handling that goes with it. The rest of this guide is about checking the line before you commit.
What is in the line
The Taokron cut-to-length line has six steps, in this order: uncoiler, feeding, leveling, measuring, cutting and stacking. In plain terms:
- Uncoiler. Holds the coil and pays the strip off. It must be sized for your heaviest coil, with the right inner diameter, outer diameter and width.
- Feeding. Pulls the strip forward into the leveler. A feeding table is on the options list.
- Leveler. A multi-roll leveler with hardened rolls. It takes out coil set and spring-back, so the sheets are ready for stamping and bending.
- Length measuring. Servo length control holds the cut length. The catalogue figure is plus or minus 0.5 mm.
- Shear. Either a servo flying shear or a hydraulic shear, chosen for your thickness and output.
- Stacker. Collects the cut sheets. An output support table is an option, and the stacking method is worth settling before you order, as covered below.
Control is PLC with touch screen. Line speed is 0 to 40 m/min, adjustable. Embossing rolls can also be added to emboss, level and cut in one line, which is where the checker plate buyers come in.
Matching thickness, width and yield strength to the leveler
The standard line covers carbon steel, galvanized steel, stainless steel and aluminium, 0.5 to 6.0 mm thick, on coil up to 1600 mm wide. Thinner, thicker or wider lines are built to order. Inside that range, a few things decide whether a leveler does the job.
Thickness against roll diameter. A leveler bends the strip over its rolls, up and down in turn, with the bend getting smaller toward the exit. To change the shape of the strip, the bend must go past the yield point of the material, at least in the outer layers. Beam bending theory puts the start of yielding at a bend diameter of about E x t / yield strength, where E is the elastic modulus and t the thickness. For 1 mm mild steel at 250 MPa yield and E of about 200 GPa, that is roughly 800 mm. Coil set only needs the outer layers to yield. Edge wave and centre buckle need the yielding to go much deeper through the thickness, which takes tighter bends: smaller work rolls and closer roll spacing. That is why thin strip needs small rolls, and why thick strip, which is stiffer and loads the rolls harder, needs larger and stronger ones.
Yield strength. Higher yield strength makes the required bend tighter, so for a given roll set, the thinnest strip you can flatten properly gets thicker as the grade gets stronger. Stainless and high-strength grades are harder to flatten than mild steel at the same thickness. This is why we ask for the grade and the yield strength, not just the material name. Aluminium has a lower modulus than steel, so the numbers differ again.
Number of rolls. More rolls mean more alternating bends, and a better chance of settling the strip flat. Roll count and roll diameter go together, and there is no single standard figure for either. They are chosen for your thickness range, width and grade. If a supplier quotes a roll count without a diameter, or a diameter without a stated thickness range, ask for both.
Width and roll support. A wide strip puts more load across the rolls, and a roll that flexes along its length bends the middle of the sheet less than the edges. Ask how the work rolls are supported across the full width. The stand-alone 6-high leveler we build supports the work rolls with back-up rolls, and the 6-High Precision Leveler page explains how that protects the surface on mirror finishes.
If your work after the cut is on thin laser blanks or finished parts, a stand-alone machine may sit alongside the line. See the Thin-Sheet Precision Leveler (0.1 to 6 mm, up to 2000 mm wide) and, for the distortion that cutting adds afterwards, our guide to part leveling after laser and plasma cutting. For plate thicker than 6 mm, look at the Heavy Plate Hydraulic Leveler, made for plate from 5 mm up.
Flying shear or stop-and-cut
Our line is offered with a servo flying shear or a hydraulic shear. As the product page describes them:
- A servo flying shear cuts without stopping the coil, so output is higher.
- A hydraulic shear stops to cut, and suits thicker material.
The choice comes down to output and thickness. Heavy output in lighter gauges points to the flying shear. Thicker coil, or modest volumes, points to stop-and-cut. Ask each supplier what the line speed is while it is cutting, not just the headline speed, and what length tolerance holds at that speed.
Length tolerance and flatness: what to ask
The catalogue length tolerance for our line is plus or minus 0.5 mm. The product page also says real accuracy depends on coil quality, speed and blade condition, and that is true of any line. When you compare quotes, ask:
- At what speed and thickness is the length tolerance stated?
- How is length measured, and how is the measuring system checked and recalibrated?
- How is squareness of the cut checked? Measure both diagonals of a sheet and compare.
- How will flatness be measured, and what figure is accepted? Lay a cut sheet on a flat table without clamping, and measure the largest gap under any edge or corner with a feeler gauge. Agree the method before you sign.
- Can the supplier run your coil, or a similar one, and show you the sheets and a video?
A line cannot fix everything in the coil. Coil set comes out well. Heavy edge wave or camber in poor coil is harder, and a leveler works better on good coil.
Coil weight, inner diameter and outer diameter
The standard line takes coil up to 1600 mm wide and 10 t. That is a ceiling, not a target. Before you order, write down:
- Your heaviest coil weight
- Inner diameter of the coils you buy
- Outer diameter at full weight, which sets the clearance around the uncoiler
- Coil width, including your widest
- How you will lift and load a coil: overhead crane, forklift or a coil car
Every decoiler is sized to the coil it carries. For the principle, see our hydraulic decoiler page, which shows a hydraulic mandrel and a coil car that loads a heavy coil without a crane.
If your coil is light, 0.5 to 1.5 mm, and the end product is strip for roll forming, a simple slitting and cut-to-length line may fit better than a full leveling line.
Floor space, foundation and stacking
The product page does not give a fixed footprint, because the length of the line depends on the longest sheet, the stacker and the coil handling you choose. Settle these with your supplier and ask for a layout drawing:
- Length of the line. Add the uncoiler, feeder, leveler, shear and stacker, plus space beyond the stacker for your longest sheet and for a forklift or crane to take the stack away.
- Coil storage. Space for the next coil beside the uncoiler, and a safe route for loading it.
- Foundation. Ask for the foundation requirements and floor load in writing. The strip runs from the uncoiler to the stacker on one centreline, so the floor must be flat and sound. Check your slab against the supplier's drawing before the machine arrives.
- Stacking. What is the stack weight, and how do you move it? Do you need paper or film between sheets, and will the stacker handle the length and width you cut?
- Power. Standard is 380 V / 50 Hz, or to your site supply. Tell us your voltage, phase and frequency early.
What we need from you to quote
- Coil material and grade, with yield strength if you know it
- Thickness range and coil width
- Coil weight, inner diameter and outer diameter
- Sheet lengths and the length tolerance you need
- Tonnes or sheets per shift
- How the sheets are stacked and moved away
- Flying shear or stop-and-cut, if you have a preference
- Site power supply (voltage, phase, frequency) and destination port
Send your coil details for a quote in 12 hours →
Taokron supplies this line. Taokron (Melbourne) handles inquiry, specification review, quotation, pre-shipment inspection, shipping and after-sales support. Production for a standard machine is 60 to 120 days; custom rolls, a cast base or a complete line take longer. The exact time is confirmed at quotation. Warranty is 12 months, with remote support included and an on-site installation engineer available on request, quoted per engineer-day. There is no list price, because each line is configured to your material, thickness and width.
FAQ
What is the difference between a straightener and a leveler on a cut-to-length line?
Both take coil set out of the strip. A leveler is built to do more: a multi-roll set bends the strip back and forth with shrinking force, so it also works on wave and edge buckle and the cut sheets lie flatter. Ask any supplier which one is in the quote, how many rolls it has and what roll diameter.
Should I choose a flying shear or a hydraulic shear?
A servo flying shear cuts without stopping the coil, for higher output. A hydraulic shear stops to cut and suits thicker material. Tell us your thickness range and output per shift and we recommend one.
How accurate is the cut length?
The catalogue figure for our line is plus or minus 0.5 mm. Real accuracy also depends on coil quality, line speed and blade condition, so ask for the figure at your speed and your thinnest and thickest material, and agree how it will be measured.
What coil size does the line take?
Coil up to 1600 mm wide and 10 t, at 0.5 to 6.0 mm thickness as standard. Thinner, thicker, wider or heavier lines are built to order. Send the coil weight, inner and outer diameter and width so the uncoiler is sized to your coil.
Can the line also emboss?
Yes. Embossing rolls can be added so one line embosses, levels and cuts to length. See our checker plate and embossing guide if that is your product.
What do I need to send for a quotation?
Material grades and yield strength, thickness range, coil width, coil weight with inner and outer diameter, sheet lengths and length tolerance, tonnes or sheets per shift, how the sheets are stacked, flying shear or stop-and-cut, and your site power supply and destination port.
Duct Shop Notes
One email a month for duct shop owners
Notes on machine choices, shop layout, duct standards and new machines. Reply "unsubscribe" any time to stop.
Thanks, you are subscribed. The first email arrives next month.