Insights · Roll forming

Roofing Sheet Roll Forming Machines in Uganda: What Local Roofing Makers Buy

What Ugandan roofing makers buy: iron sheet in gauge 28, 30 and 32, corrugated, box profile and tile sheet, plus ridge cap, gutter and downpipe machines. UNBS gauge rules, VAT and EAC duty, 240/415 V power, the Mombasa route and what to send for a quote.

Who this guide is for

This guide is for a roofing maker in Uganda who buys coil and sells formed iron sheet to builders, hardware shops and contractors in Kampala, Jinja, Mbarara or another town, rather than a large coil-coating mill. The questions are which machines make sense, how thin your sheet is against the machine range, and what to check before you order from overseas.

What the Ugandan market asks for

Demand. A September 2026 opinion piece by the head of a Kampala hardware firm, republished on AllAfrica, says the Uganda Bureau of Statistics puts 75% of households in homes roofed with iron sheets, and that the 2024 census counted over 10.7 million households and a housing deficit of 2.4 million units. Other reports put the deficit lower, so treat it as a range and count your own volume before you size a line.

Profiles. Uganda Baati lists Versatile, Orientile, Romantile and Dumuzas in its range, and Roofings Group sells galvanized and pre-painted sheet. Profile names are brand names, not drawings. Your own sample sheet is the reference, and we build the rolls to it.

Gauge. Ugandan sellers sell by gauge number: 28, 30 and 32. A UNBS draft standard for aluminium-zinc coated sheet (DEAS 410:2020) lists gauge 32 at 0.20 mm and gauge 30 at 0.25 mm, each with a 10% tolerance. We could not find a confirmed figure for gauge 28. This matters for machine choice, because our trapezoidal, glazed tile, ridge cap, gutter and downpipe machines are catalogued from 0.3 mm. Gauge 30 and 32 sheet is below that range. If you roll thin sheet, say so in your first message. Do not assume it will run.

Standards and enforcement. US EAS 11:2013, galvanized plain and corrugated steel sheets, was published in the Uganda Gazette in January 2014. A UNBS notice reposted on a pre-shipment inspection portal, and a 2015 news report on the colour coding, say gauge 32 sheet must be marked blue, gauge 30 red and gauge 28 black, and that importing galvanized roofing sheet and coil in G34 is prohibited. UNBS has said in the past that some makers sell gauge 32 pre-painted sheet marked as gauge 30. We could not see a current dated notice, so confirm the rules in force with UNBS. The machine does not decide base metal, thickness or coating. Your coil does. The machine decides cover width, rib height, straightness and cut length.

Machines on our range and why a Ugandan roofing maker would buy each

Every line is built to your drawing. The figures below are catalogue figures from each machine page. Final figures are confirmed on the quotation.

Trapezoidal and corrugated roof sheet machine

This is the core machine for corrugated and box profile iron sheet. One machine forms one profile, and the rolls follow the sheet your customers already buy. It takes 0.3 to 0.8 mm material from 914, 925, 1000 or 1250 mm coil, with 18 roll stations (depends on the profile), a 5.5 kW main motor, a 3 kW hydraulic station, hydraulic post-cut and a forming speed of 10 to 20 m/min. Corrugated cover widths are 762, 838.2 or 1066.8 mm, and the trapezoidal widths are listed on the page. See the trapezoidal and corrugated roof sheet machine.

Double layer roof sheet machine

If you sell corrugated and box profile side by side, this puts both on one frame with one cutting station and one control cabinet. It is catalogued for 0.3 to 1.0 mm, coil 1000 or 1250 mm, a 7.5 kW main motor, a 4 kW hydraulic station and 10 to 15 m/min. See the double layer roof sheet machine.

Glazed tile machine

Tile-effect sheet gives a tile look at a lower weight than clay. A hydraulic press puts in the step at each tile row, so speed is 3 to 5 m/min. Plan output on that figure. It is catalogued for 0.3 to 0.8 mm and coil 914, 1000, 1220 or 1250 mm, with a 5.5 kW main motor and a 5.5 kW hydraulic station. See the glazed tile machine.

Ridge cap machine

A roof needs ridges and valleys as well as sheet. The machine forms round ridge, trapezoid ridge and V-valley flashing from 300, 456 or 462 mm coil, 0.3 to 0.8 mm, at 10 to 15 m/min with 12 roll stations (depends on the profile), a 4 kW main motor and a 5.5 kW hydraulic station. See the ridge cap machine.

Gutter and downpipe machines (add-ons)

Gutter and downpipe can come from the same coil stock as the roof. The gutter machine takes 247, 303, 635 or 645 mm strip at 12 to 15 m/min with 19 roll stations (depends on the profile). The downpipe machine takes 180, 300 or 342 mm strip at 8 to 10 m/min with 18 roll stations (depends on the profile). Both are catalogued for 0.3 to 0.8 mm with a 5.5 kW main motor and a 4 kW hydraulic station. See the gutter machine and the downpipe machine.

C/Z purlin machine (add-on)

Steel-frame buildings carry roof sheet on purlins, so a sheet shop can sell both. The machine makes C, Z and U purlins in 1.5 to 3 mm steel, web 100 to 300 mm, flange 40 to 80 mm and lip 15 to 20 mm, with 16 roll stations (depends on the profile), an 18.5 kW main motor and an 11 kW hydraulic station. It is the heaviest machine here, so check your supply and generator size first. See the C/Z/U purlin machine and our purlin buyer guide.

Decoiler and slitting line

A hydraulic decoiler holds the coil and feeds the line. See the hydraulic decoiler. If you buy wide coil and cut your own strip for ridge cap or gutter, the slitting and cut-to-length line is catalogued for 0.5 to 1.5 mm and coil 1250 to 1500 mm at 8 to 10 m/min. Its range starts at 0.5 mm. All lines are in the roll forming range.

Check metal and thickness before anything else

Our catalogue lists a thickness range, not a metal list. Galvanized steel, aluminium-zinc coated sheet and pre-painted coil behave differently in the rolls. Tell us the metal, coating, temper and exact thickness in millimetres in your first message, not just the gauge number, because gauge tables differ between standards. We check them before we quote.

Power, import taxes and delivery

  • Power: UEDCL tariff schedules give single phase at 240 V and three phase at 415 V, and reference tables list 50 Hz. Uganda Manufacturers Association members have reported frequent outages and voltage surges. Measure at your workshop and send us voltage, phase and frequency. Tell us your generator size if you run one.
  • Duty: duty follows the East African Community Common External Tariff, which since 1 July 2022 has four bands: 0%, 10%, 25% and 35%. The EAC describes the 0% band as covering raw materials and capital goods. We have not confirmed which tariff line a roll forming machine falls under, and Uganda also uses country-specific stays of application, so get the classification from your clearing agent or URA.
  • VAT: PwC lists the standard rate at 18%. It also describes a facility where VAT on imported plant and machinery is deferred and later waived on approval, and URA publishes a discharge process. Whether your machine qualifies depends on your business, so ask your accountant.
  • Route: machines normally arrive by sea at Mombasa and travel by road on the Northern Corridor. Uganda accounted for about two thirds of transit volume through Mombasa in 2024. A January 2026 report put a one-way truck run to Kampala at 3.7 to four days, with border delays stretching round trips past ten.
  • Delivery: about 60 working days from drawing approval and deposit, then sea freight to the port you name.

What we need from you to quote

  • A sample sheet piece measured with a tape, or a profile drawing with dimensions
  • Metal, coating and exact thickness in millimetres, plus the gauge number you sell
  • Coil width and coil weight you buy
  • Sheet lengths you cut and rough daily output
  • Whether you also want ridge cap, C/Z purlin, gutter or downpipe
  • Site power supply (voltage, phase, frequency), generator size if any, and destination town or port

Send your roofing sheet profile for a quote in 12 hours →

Taokron roll forming machines are built to your drawing. Taokron (Melbourne) handles drawing review, quotation, pre-shipment inspection, shipping and after-sales support. Warranty is 12 months from arrival at your factory, with remote video support included and an on-site installation engineer available on request, quoted per order. Since 1994 our team has supplied machines to buyers in 100+ countries. Neighbouring-market guides are the Kenya roof sheet guide and the Tanzania roofing sheet guide.

FAQ

Which gauges do Ugandan buyers ask for, and will your machine run them?

Ugandan sellers talk in gauge 28, 30 and 32. A UNBS draft standard for aluminium-zinc coated sheet lists gauge 32 at 0.20 mm and gauge 30 at 0.25 mm, and we could not confirm the figure for gauge 28. Our trapezoidal and corrugated machine is catalogued for 0.3 to 0.8 mm, so thinner gauges sit below the range. Send the exact thickness in millimetres and we check it before we quote.

Does the machine make my sheet comply with UNBS requirements?

No. Base metal, thickness tolerance and coating come from your coil, not from the machine. The machine controls cover width, rib height, straightness and cut length. A UNBS notice points to US EAS 11:2013 for galvanized sheet and sets colour marking by gauge. Check the current requirements with UNBS and your coil supplier.

What power supply do I need to tell you about?

Reference tables list Ugandan mains as 240 V single phase and 415 V three phase at 50 Hz. Uganda Manufacturers Association members have reported outages and voltage surges, so measure at your workshop and send us voltage, phase, frequency and any generator size, so the motors and cabinet are matched to it.

What import duty and VAT apply to a roll forming machine in Uganda?

Duty follows the East African Community Common External Tariff, whose lowest band is 0% and is described as covering capital goods. Uganda's standard VAT rate is 18%, and a VAT deferral facility exists for imported plant and machinery. We have not confirmed the exact line or rate for a roll forming machine, so ask your clearing agent or URA to confirm the classification and the landed taxes before you sign.

How does a machine reach Kampala, Jinja or Mbarara?

Containers normally go by sea to Mombasa, then by road on the Northern Corridor into Uganda. A January 2026 press report put a one-way truck run from Mombasa to Kampala at 3.7 to four days, with border delays pushing round trips past ten. Tell us your destination and we quote shipping to Mombasa or the port you name.

Can I start with one machine and add ridge cap or gutter later?

Yes. A common route is to start with the sheet machine for the profile their customers already buy, then add ridge cap, gutter or downpipe from the same coil stock. Each profile needs its own roll set, so tell us what you plan to add and we size the decoiler and power for it.

Duct Shop Notes

One email a month for duct shop owners

Notes on machine choices, shop layout, duct standards and new machines. Reply "unsubscribe" any time to stop.

12-hour reply

Send a sample sheet or drawing, thickness and coil width. Ryan Tao replies within 12 hours with a configuration, lead time and price.

Ask an engineer

Engineer reply

Ask an engineer about this guide

Describe your job and what you are trying to make. Ryan Tao replies within 12 hours.

Guide: Roofing Sheet Roll Forming Machines in Uganda: What Local Roofing Makers Buy