Who this guide is for
This guide is for a New Zealand business that buys coil and wants its own forming line: a long-run roofing and cladding maker, a purlin or steel framing fabricator, a builder-fabricator, or a rainwater goods supplier. It does not cover large coil-coating mills. The questions are which machine fits which job, what your coil and the Building Code mean for the machine, and what to check before you import.
The New Zealand market in 2026
Housing consents. Stats NZ reports that 41,091 new dwellings were consented in the year ended September 2026, up 18 percent on the year before. That is 7.7 new dwellings consented per 1,000 residents, against 6.6 a year earlier. The seasonally adjusted monthly figure fell 7.9 percent in September after rising 5.3 percent in August, so the trend is not a straight line.
Non-residential work. The annual value of non-residential building work consented was $8.7 billion, down 3.1 percent on the year ended September 2025.
What that means for a forming shop. Houses, sheds, rural buildings and commercial roofs all need roof and wall sheet, ridge, gutters and framing members. A maker that runs its own line can match profile, colour and length to the job. Consent numbers do not size your line, so use your own order book.
Standards and the Building Code: what the machine does and does not decide
- Clause B2 Durability. The Metal Roofing Manufacturers Code of Practice says B2 requires 15 years to perforation for claddings that are easily accessed for replacement, and 50 years for structural elements and elements that are hard to access or replace. It also notes that B2 asks for 50 years on flashings that need the cladding removed to replace them, while E2/AS1 Table 20 asks for 15.
- Clause E2 External moisture. MBIE published the fourth edition of Acceptable Solution E2/AS1 on 28 July 2025, and the previous edition could be used until 31 July 2026.
- AS 1397:2021 covers continuous hot-dip metallic coated steel sheet and strip, including zinc coatings alloyed with aluminium and magnesium. E1/AS1 for surface water cites it.
- NZS 3604:2011 is the standard for timber-framed buildings that Acceptable Solution B1/AS1 refers to. Light steel framing goes a different way: the NASH Standard Part 1 sets design criteria for steel-framed buildings, and MBIE's building code hub lists the 2016 edition as an alternative solution for B1. That edition cites AS/NZS 4600 for cold-formed steel. Confirm which edition and which route your engineer and council accept.
The machine controls cover width, rib height, straightness, hole position and cut length. It does not control base metal, coating or yield strength. Those come from your coil and your engineering. We build the rolls to your drawing and your sample, so name the profile by its dimensions, not by a brand name.
Coastal exposure and coil choice
New Zealand roofs are rarely far from salt air. The Code of Practice sets out six corrosion zones, A to F, by first-year mild steel corrosion rate. Zone B is most dry rural land about 50 km from the coast, zone C is low marine influence, zones D and E are severe and very severe marine, and zone F is an exposed site very close to breaking surf. NZS 3604 uses zones B, C and D, and the Code splits D into E and F. The Code also says boundaries are hard to define, that marine influence usually reaches only a few hundred metres inland, and that open land, shade and low rainfall can change the result.
For a forming shop this decides your coil specification, not your machine. A roof near the sea and a roof 60 km inland may use different coatings, and your customers will ask which one you supplied. Send us the grade, coating, base metal thickness in millimetres and coil width in your first message. Our roofing machines are catalogued by a thickness range, not a metal list, so we check your specific coil before we quote. Cut ends and punched holes expose bare steel, so ask your coil supplier how they should be treated on coastal jobs, and note the Code says unwashed surfaces can corrode two to three times faster than cleaned ones.
Which machine fits which business
Every line is built to your profile drawing. The figures below are catalogue figures from each machine page, and final figures are confirmed on the quotation. We quote per profile and line configuration.
Roofing and cladding makers
The core machine is the trapezoidal and corrugated roof sheet machine. It takes 0.3 to 0.8 mm material from 914, 925, 1000 or 1250 mm coil, with 18 roll stations (depends on the profile), a 5.5 kW main motor, a 3 kW hydraulic station, hydraulic post-cut and a forming speed of 10 to 20 m/min. Each machine forms one profile, which is why we ask for your profile drawing. If you sell two profiles and lack floor space, the double layer roof sheet machine puts two on one frame. It is catalogued for 0.3 to 1.0 mm, coil 1000 or 1250 mm, with a 7.5 kW main motor, a 4 kW hydraulic station and 10 to 15 m/min.
A roof also needs a ridge. The ridge cap machine forms ridge capping and V-valley flashing from 300, 456 or 462 mm coil, 0.3 to 0.8 mm, at 10 to 15 m/min with 12 roll stations (depends on the profile).
Rainwater goods makers
The gutter machine makes half-round, box and large industrial gutters from 247, 303, 635 or 645 mm strip, 0.3 to 0.8 mm, at 12 to 15 m/min with 19 roll stations (depends on the profile). The downpipe machine forms round or rectangular downpipe from 180, 300 or 342 mm strip at 8 to 10 m/min with 18 roll stations (depends on the profile). If you buy wide coil and want narrower strip, the slitting and cut-to-length line is catalogued for 0.5 to 1.5 mm and coil 1250 to 1500 mm at 8 to 10 m/min. Its range starts at 0.5 mm, so it does not cover the thinnest coil.
Purlin and shed makers
The C/Z/U purlin machine makes C, Z and U sections in 1.5 to 3 mm steel, web 100 to 300 mm, flange 40 to 80 mm and lip 15 to 20 mm, with 16 roll stations (depends on the profile), an 18.5 kW main motor, an 11 kW hydraulic station, and punching plus hydraulic post-cut. If you need both shapes, the quick-change purlin machine switches between C and Z on one line with pre-cut, so no cutting die per size is needed. For choosing between them, see our purlin buyer guide.
Steel framing fabricators
The stud and track machine makes drywall studs, tracks, furring channels and wall angles in 0.3 to 1.0 mm, with 14 roll stations (depends on the profile), a 5.5 kW main motor and 10 to 20 m/min. For framing houses, the light steel framing machine punches service holes, bolt holes and dimples in line. Its page has no spec table, so we give the specifications per order after we see your framing system and software output.
Floor deck
The floor deck machine is for composite deck in 0.8 to 1.5 mm from 1000, 1220 or 1250 mm coil, with 26 roll stations (depends on the profile), a 22 kW main motor and 10 to 15 m/min. It is the heaviest line in this guide, so check your power first.
Feeding the line
A hydraulic decoiler holds the coil and feeds the machine, sized to your coil weight, inner diameter and width, with a hydraulic coil car as an option. See all lines in the roll forming range.
Power, import taxes and rules
- Power: WorkSafe describes the standard New Zealand supply as 230 V, or 400 V multi-phase, at 50 Hz. Tell us your voltage, phase, frequency and any supply limit at your site, and we match the motors and cabinet. Your electrician confirms the connection.
- GST: NZ Customs says GST is 15 percent, calculated on the Customs value plus any duty and your shipping and insurance costs. Business importers can pay by deferred payment, through a broker deferred credit account, or per transaction. Inland Revenue says you can claim it back if you are GST registered and use the goods solely to make taxable supplies. Ask your accountant about your case.
- Duty and classification: the rate depends on how your machine is classified. We have not confirmed it for your line, so ask your customs broker before you sign.
- Biosecurity: MPI's Import Health Standard for Vehicles, Machinery and Parts applies to new and used machinery. In the version we read, dated 11 August 2021, machinery must arrive clean and free of biosecurity contaminants and regulated pests, sea containers must meet the Sea Containers standard, and wood packaging must meet the Wood Packaging Material standard. Standards get amended, so ask your broker to check the current version, and tell us early so we can pack and document the machine to suit.
What we need from you to quote
- A profile drawing with dimensions, or a sample piece measured with a tape
- Coil grade, coating and base metal thickness in millimetres
- Coil width and coil weight you buy
- Product lengths you cut and rough daily output
- Which other lines you may add later: ridge cap, gutter, downpipe, purlin or framing
- Site voltage, phase and frequency, and your destination port or town
Send your profile drawing for a quote →
Taokron roll forming machines are built to your drawing, and we build our machines in our own factory. You can reach us on WhatsApp at +61 435 074 994. An installation engineer is available on request and quoted separately. Warranty is 12 months from arrival at your factory. Since 1994 our team has supplied machines to buyers in 100+ countries. If you also work across the Tasman, see our Australia guide, and for other markets the Kenya, Nigeria and Uganda guides.
FAQ
Which standards apply to the sheet and sections I make?
The machine does not make a product comply. Compliance comes from your coil, your profile design and the route your customer or engineer uses under the Building Code. Common references are Building Code clauses B2 Durability and E2 External moisture for roofing, AS 1397 for metallic-coated sheet and strip, and AS/NZS 4600 and the NASH Standard Part 1 for light steel framing. Check the current editions and what your customers, engineers or council ask for.
How does coastal exposure affect the coil I should run?
Coating and base metal come from your coil, not from the machine. The Metal Roofing Manufacturers Code of Practice describes corrosion zones A to F based on first-year mild steel corrosion. Ask your coil supplier or the Code of Practice which coating suits each site, and tell us the coil you plan to buy so we check it against our thickness range.
Can I run both C and Z purlins on one line?
Yes. The quick-change purlin machine switches between C and Z sections on one line, catalogued for 1.5 to 3 mm steel, web 100 to 300 mm. The strip goes through feeding and levelling, punching and cutting before forming, so you do not need a cutting die for each size. Send your section sizes and hole pattern for the exact configuration.
What power supply do your machines need in New Zealand?
WorkSafe describes the standard New Zealand supply as 230 V, or 400 V multi-phase, at 50 Hz. Our machines are configured to the supply you give us. The larger lines have big motors, for example 18.5 kW on the purlin machine and 22 kW on the floor deck machine, so have your electrician check your supply before you order.
What import taxes and rules apply to a roll forming machine?
NZ Customs charges GST at 15 percent, calculated on the Customs value plus any duty and your shipping and insurance costs. A GST-registered business can claim it back if the goods are used solely to make taxable supplies. Duty depends on the tariff classification, so we have not quoted a rate: ask your customs broker. Machinery also falls under the MPI Import Health Standard for Vehicles, Machinery and Parts, which asks for clean machines and has rules for containers and wood packaging.
What about installation and warranty?
An installation engineer is available on request and quoted separately, and warranty is 12 months from arrival at your factory. You can reach us on WhatsApp on +61 435 074 994 or through the quote form on this page.
Duct Shop Notes
One email a month for duct shop owners
Notes on machine choices, shop layout, duct standards and new machines. Reply "unsubscribe" any time to stop.
Thanks, you are subscribed. The first email arrives next month.