Who this guide is for
This guide is for an Australian business that buys coil and wants its own forming line: a roof and wall cladding maker, a purlin or steel framing fabricator, a shed or carport builder, or a rainwater goods supplier. It does not cover large coil-coating mills. The questions are which machine fits which job, what your coil and standards mean for the machine, and what to check before you import.
The Australian market in 2026
Housing pipeline. The National Housing Accord sets a target of 1.2 million well-located new homes over five years from 1 July 2024. The National Housing Supply and Affordability Council's August 2026 quarterly report estimates the target will be reached in the December quarter of 2030, a quarter later than it expected earlier, and says quarterly building approvals are up 26 percent and commencements up 15 percent on the quarter before the Accord began.
Approvals. The Australian Bureau of Statistics reported seasonally adjusted total dwelling approvals of 17,948 for September 2026, up 5.1 percent on the month. Private sector house approvals were 10,432, the ninth month in a row above 10,000. Monthly figures are revised, so size a line on your own order book.
What that means for a forming shop. Houses, sheds, rural buildings, warehouses and extensions all use roof and wall sheet, purlins, gutters and framing members. A maker that runs its own line can match profile, colour and length to the job.
Standards and coil: what the machine does and does not decide
- AS 1397 covers continuously hot-dip metallic-coated steel sheet and strip up to 5.0 mm thick, including the grade and the coating. High-tensile grades are written as G550, meaning a 550 MPa minimum yield.
- AS 1562.1:2018 is the standard for design and installation of metal roof and wall cladding. Design is driven by wind pressure, thermal movement and fixing. In cyclonic regions the loads and fixing details are more demanding, so check with your engineer or the cladding supplier you follow.
- AS/NZS 4600 covers cold-formed steel structures, which is the design basis for purlins, girts and light steel framing members. The NASH Standard for residential and low-rise steel framing is another route the National Construction Code has recognised for steel framing. Editions change, so confirm which one your project references.
- AS/NZS 2179.1:2014 sets requirements for metal rainwater goods, accessories and fasteners.
The machine controls cover width, rib height, straightness, hole position and cut length. It does not control base metal, coating or yield strength. Those come from your coil and your engineering. We build the rolls to your drawing and your sample, so name the profile by its dimensions, not by a brand name.
Thin high-tensile coil
Australian roofing is often rolled from G550 coil in thin base metal thicknesses. Manufacturer datasheets list common roofing profiles at 0.42 and 0.48 mm base metal thickness. High-tensile thin coil is springy. Tell us the grade, coating, base metal thickness in millimetres and coil width in your first message. Our catalogue lists a thickness range, not a metal list, so we check the specific coil before we quote.
Which machine fits which business
Every line is built to your profile drawing. The figures below are catalogue figures from each machine page, and final figures are confirmed on the quotation. We quote per profile and line configuration.
Roofing and cladding makers
The core machine is the trapezoidal and corrugated roof sheet machine. It takes 0.3 to 0.8 mm material from 914, 925, 1000 or 1250 mm coil, with 18 roll stations (depends on the profile), a 5.5 kW main motor, a 3 kW hydraulic station, hydraulic post-cut and a forming speed of 10 to 20 m/min. Each machine forms one profile, which is why we ask for a custom profile to your drawing. If you sell two profiles and lack floor space, the double layer roof sheet machine puts two on one frame. It is catalogued for 0.3 to 1.0 mm, coil 1000 or 1250 mm, with a 7.5 kW main motor, a 4 kW hydraulic station and 10 to 15 m/min.
A roof also needs a ridge. The ridge cap machine forms ridge capping and V-valley flashing from 300, 456 or 462 mm coil, 0.3 to 0.8 mm, at 10 to 15 m/min with 12 roll stations (depends on the profile).
Rainwater goods makers
The gutter machine makes half-round, box and large industrial gutters from 247, 303, 635 or 645 mm strip, 0.3 to 0.8 mm, at 12 to 15 m/min with 19 roll stations (depends on the profile). The downpipe machine forms round or rectangular downpipe from 180, 300 or 342 mm strip at 8 to 10 m/min with 18 roll stations (depends on the profile). If you buy wide coil and want narrower strip, the slitting and cut-to-length line is catalogued for 0.5 to 1.5 mm and coil 1250 to 1500 mm at 8 to 10 m/min. Its range starts at 0.5 mm, so it does not cover the thinnest coil.
Purlin and shed makers
The C/Z/U purlin machine makes C, Z and U sections in 1.5 to 3 mm steel, web 100 to 300 mm, flange 40 to 80 mm and lip 15 to 20 mm, with 16 roll stations (depends on the profile), an 18.5 kW main motor, an 11 kW hydraulic station and punching in line. If you need both shapes, the quick-change purlin machine switches between C and Z on one line with pre-cut and punching, so no cutting die per size is needed. For choosing between them, see our purlin buyer guide.
Steel framing fabricators
The stud and track machine makes drywall studs, tracks, furring channels and wall angles in 0.3 to 1.0 mm, with 14 roll stations (depends on the profile), a 5.5 kW main motor and 10 to 20 m/min. For framing houses, the light steel framing machine punches service holes, bolt holes and dimples in line. Its page has no spec table, so we give the specifications per order after we see your framing system and software output.
Floor deck and solar racking
The floor deck machine is for composite deck in 0.8 to 1.5 mm, with 26 roll stations (depends on the profile), a 22 kW main motor and 10 to 15 m/min. The solar mounting channel machine forms 41.3 mm C channels in 1.5 to 3 mm, with 28 roll stations (depends on the profile), a 30 kW main motor and a servo tracking cut. These are the heaviest lines here, so check your power first.
Feeding the line
A hydraulic decoiler holds the coil and feeds the machine, sized to your coil weight, inner diameter and width, with a hydraulic coil car as an option. See all lines in the roll forming range.
Power, import taxes and rules
- Power: most of Australia is nominally 230 V single phase and 400 V three phase at 50 Hz. Tell us your voltage, phase, frequency and any supply limit at your site, and we match the motors and cabinet.
- GST: the Australian Taxation Office describes GST on a taxable importation as 10 percent of the value of the taxable importation, which is the customs value plus any duty plus the international freight and insurance costs to Australia. A GST-registered business can usually claim a credit if it imports for a creditable purpose. Ask your accountant.
- Duty and classification: the rate depends on how your machine is classified. We have not confirmed it for your line, so ask your customs broker before you sign.
- Safety and compliance: under the model work health and safety laws, importers and suppliers of plant carry their own duties, and the AS/NZS 4024 series is the machinery safety reference. We cannot give legal or electrical compliance advice here. Ask your safety adviser and electrician what your site and state need, and tell us early so we can supply machine documents.
What we need from you to quote
- A profile drawing with dimensions, or a sample piece measured with a tape
- Coil grade, coating and base metal thickness in millimetres
- Coil width and coil weight you buy
- Product lengths you cut and rough daily output
- Which other lines you may add later: ridge cap, gutter, downpipe, purlin or framing
- Site voltage, phase and frequency, and your destination port or town
Send your profile drawing for a quote in 12 hours →
Taokron roll forming machines are built to your drawing, and we build our machines in our own factory. Our Australian office in Box Hill North, Victoria, handles drawing review, quotation, inspection, shipping and after-sales support. You can reach us on WhatsApp at +61 435 074 994 and we reply within 12 hours. Installation and commissioning are quoted per engineer-day. Warranty is 12 months from arrival at your factory. Since 1994 our team has supplied machines to buyers in 100+ countries, and our roofing guides for other markets include the Kenya, Nigeria, Tanzania, Ghana and Uganda guides.
FAQ
Which standards apply to the sheet and sections I make?
The machine does not make a product comply. Compliance comes from your coil, your profile design and the standard the product is sold under. Common references are AS 1397 for metallic-coated sheet and strip, AS 1562.1 for metal roof and wall cladding, AS/NZS 4600 for cold-formed steel structures and AS/NZS 2179.1 for metal rainwater goods. Check the current edition and what your customers or engineers ask for.
Can your roofing machine run thin high-tensile coil?
Our trapezoidal and corrugated machine is catalogued for 0.3 to 0.8 mm, and manufacturer datasheets list common high-tensile roofing coil at 0.42 and 0.48 mm base metal, which sits inside that range. Final suitability depends on your exact coil, so send the grade, coating and thickness in millimetres and we check it before we quote.
Can I run both C and Z purlins on one line?
Yes. The quick-change purlin machine switches between C and Z sections on one line, catalogued for 1.5 to 3 mm steel, web 100 to 300 mm. The strip is levelled, punched and cut to length before forming, so you do not need a cutting die for each size. Send your section sizes and hole pattern for the exact configuration.
What power supply do your machines need in Australia?
Most of Australia uses 230 V single phase and 400 V three phase at 50 Hz. Our machines are configured to the supply you give us. The larger lines have big motors, for example 18.5 kW on the purlin machine and 30 kW on the solar channel machine, so have your electrician check your supply before you order.
What import taxes and rules apply to a roll forming machine?
GST at 10 percent applies to a taxable importation, charged on the value of the taxable importation (customs value, duty, and international freight and insurance), and a GST-registered business can usually claim it back as a credit. Duty depends on the tariff classification, so we have not quoted a rate: ask your customs broker. Under Australian work health and safety laws, importers and suppliers of plant have their own duties, so ask your safety adviser what you need.
Do you have anyone in Australia, and what about installation?
Yes. Taokron has an office in Box Hill North, Victoria, and you can reach us on WhatsApp on +61 435 074 994. We reply within 12 hours. Installation and commissioning are quoted per engineer-day, and warranty is 12 months from arrival at your factory.
Duct Shop Notes
One email a month for duct shop owners
Notes on machine choices, shop layout, duct standards and new machines. Reply "unsubscribe" any time to stop.
Thanks, you are subscribed. The first email arrives next month.